The Pantser

Sounds like a thermal runaway where a temperature changed too quickly and the code interpreted that as a fire or risk of fire and shut down. A lot of times that can be helped with a silicone sock and a PID tuning. Another thing is the ceramic heater core is going bad and it can’t keep a stable temp above a point. Heater cores are cheap and easy to change. The heater core is considered a consumable part and usually comes in multiple packs.

Might wanna switch that F to a C.

PETG is picky about layer heights and speed.

Thick and slow for PETG. I usually double my layer height vs what I would print in PLA. With my .6 nozzle I print with .3 layer and cut my speed down to 50% for the first layer. Since you said it happens mid print you might be printing too fast for the first few layers and it is getting too high because the layer is not cooling enough and it starts curling. You can also try reducing flow if your nozzle is worn and it’s allowing more plastic than the sclicer expects which will cause too high layers and scraping.

Oh and it sounds like it’s too hot too. 80° bed in a enclosure could cause the chamber to get too hot and not allow the layers to cool fast enough and so you will see curling while printing. Lower the bed to 40-50 and monitor chamber temps. Maybe open the doors a crack. You only need an enclosure for PETG if the room is drafty.

That’s 2 heading cards, one is set as the title and the other as subtitle. The title has the navigation option turned on to navigate to that room. And the subtitle is just filled with entities. I then use a entities card set with just the divider. It’s a messy way to do it but it was the best I could figure.

Just to give an idea what I use it for based on my Home Dashboard

Office is under remodel which is why the sensors are offline.

Been using it for awhile now. Do we have a way to use our phones as the play yet? I want to be able to listen on my phone with headphones or even in my car with Android Auto. I would love to be able to delete my Spotify app. I still use the service because the radio feature is still much better than MA. But once I can do everything that Spotify can be I can cancel my Spotify account.

Now can we have an overlay that compares the counties with their political majority.

That is a bed leveling issue. It’s too far away where there are gaps and too close where there is rippling. Run a bed leveling procedure and if the model allows for manual leveling you should go through that and then do another mesh leveling.

Also clean your build plate with soap and water and avoid touching it with bare hands.

So online farmers/flea market?

Why not start the boycott of all of those now? Why wait and allow them to prepare for it?

He’s just backed up and needs to make a poopy, constipation is uncomfortable.

I started with a cheap kit from a company that no longer exists. Over the last 15 years I have added and upgraded parts. I would say buy what you can afford and then upgrade as you go. The uv and remineralizers are nice to have but not needed. Just be sure to get a 5 stage to start. 3 stage pre filters plus membrane and charcoal. Another good upgrade is a permeate pump, it boosts the efficiency and saves water on the waste. I have my waste water fed out to water my garden in the summer.

I once even tried to add a Deionization filter before the minerals that way it was almost 0ppm tds before adding back the minerals but it seemed to destroy my mineral cart and made my water smell fishy.

I am not an expert just a homeowner with 15 years of filtering my own water.

Which is strange because you would think keeping the price low enough to sway customers away from other services or low enough it’s forgettable (gym membership style) or just low enough to keep people from canceling would net them more customers and make up for the lower rates.

But no they keep increasing and driving more people away which in turn causes them to raise rates again this is a death spiral.

I would take Theranos giving a diagnosis over AI. At least Theranos faked it and used real labs for their grift.

How does this work with FOIA?

More drives mean more heat and more power usage. Better to have two large with parity enabled. The chances of both failing is very rare. Should be using an online backup service like backblaze or having a plan to take a copy off-site.

Because of googles enshitification I have stopped using voice to control my home entirely. I invested in many scene remotes and built extensive automations. I’ve come to not miss voice control at all. But here’s to you that want this either for assistive needs or just because. I just need to get a few more local TTS speakers for alerts.

My tree has 500 ws2812 pixels that I printed c9 covers for. It’s running wled and added to HA so it turns off and on with entering the room or watching TV. Added bonus is the addition of a mic so it dances to the music.